Views: 0 Author: Site Editor Publish Time: 2026-11-17 Origin: Site
In short: in November 2026, a group of overseas distributors and private-label buyers visited Hunan Haipuming Technology, the coloured contact lens factory of Hunan Liangguo Technology Group. They walked the line their own orders run on — injection, sandwich printing, extraction, 121 °C sterilization, 12 inspection steps, packing — and checked the four things a sample can never show: pigment origin, print registration, sterilization records and batch traceability.
A contact lens cannot be inspected as a product. It is a 0.08 mm transparent film sealed in a blister; the defects that actually cost a distributor money — an iris print sitting 0.2 mm off centre, a base curve that drifts between lots, a seal that fails in a humid warehouse — are invisible when you hold a sample.
So experienced buyers inspect the process instead. That was the purpose of this visit: not a showroom photograph, but a walk through the line that has to produce order 1 and order 30 to the same standard.
The visit opened at the group's corporate wall — subsidiary companies, the chairman's introduction, corporate culture — the same wall every visiting delegation passes.
What that wall explains is why Haipuming can be audited end to end:
Hunan Liangguo Technology Group is the parent. Haipuming is its coloured contact lens factory and the only manufacturer of coloured lenses in Hunan Province.
Construction started in 2018; the factory obtained its CFDA registration and began production in 2020; Phase I was completed in 2021 with an annual output of 120 million lenses, and Phase II construction followed.
Around 1,000 employees, including engineers and trained production staff, plus 500+ sets of production equipment and 70 inspection instruments.
For a buyer, the relevant point is narrower: the entity that holds the registration is the entity that runs the line. There is no gap between the certificate and the machine that made the lens.
1. Injection and moulding. Automatic precision injection machines, fully moulded filling machines and semi-mould injection lines run in parallel — 500+ sets of equipment in total. The delegation watched mould tooling changeover, because tool wear is where diameter and base curve begin to drift.
2. Printing — the sandwich layer. Colour lenses are built in a sandwich construction: the pigment layer is sealed between two hydrogel layers so it never contacts the eye. Pigments come from Korea's Hyundai Pigments, approved by the U.S. FDA for use in cosmetic contact lenses. Buyers inspected printed lenses under magnification for iris registration and edge coverage — the two defects that surface at retail as "the pattern looks off" and "there is a halo".
3. Extraction and hydration. Haipuming's own lens extraction process is designed to remove residual monomer from the lens before hydration — the step that decides how the lens behaves on a sensitive eye. It is the technical point most often skipped in a factory tour, and the one buyers ask about most.
4. Sterilization. Terminal sterilization runs at 121 °C moist heat for 30 minutes, F0 ≥ 30, with the sterility assurance level held at one part per million. This is where a factory is separated from a workshop: the parameters are recorded per load, and the record travels with the batch.
5. Inspection and packing. Of the 20+ procedures in production, 12 are inspection steps, carried out at each level. Lens screening runs at 17× magnification alongside automated vision checks. Rejected lenses are pulled, logged and traced to the mould and the lot. Packing then prints batch number, production date and expiry per destination market.
Checkpoint | The question behind it | What the visit showed |
|---|---|---|
Pigment origin | "Will my registration file survive an audit?" | Hyundai Pigments (Korea), FDA-approved for cosmetic contact lenses |
Print registration | "Will the iris sit centred on every lens?" | Sandwich construction; printed lenses checked under magnification on the line |
Sterilization records | "What do you show me if a customer reports an eye issue?" | 121 °C / 30 min, F0 ≥ 30, SAL 1 ppm, recorded per load |
Batch traceability | "Can you trace this blister back to the mould?" | Lot-level records archived and retrievable with the shipment |
Two operational questions came up as well: trial quantities on a new design, and how fast a private-label run can start once artwork is approved. Both are answered by the same structure — design, tooling, printing, sterilization and packing sit inside one factory, so a new SKU does not wait on a third party.
Item | Detail |
|---|---|
Entity | Hunan Haipuming Technology Co., Ltd. — coloured contact lens factory of Hunan Liangguo Technology Group |
Position | The only coloured contact lens manufacturer in Hunan Province |
Timeline | Built from 2018; CFDA registration and production from 2020; Phase I completed 2021 at 120 million lenses per year |
Workforce | ~1,000 employees, including engineers and trained production staff |
Equipment | 500+ production machines; 70 inspection instruments |
Colour technology | Sandwich printing; Hyundai Pigments (Korea), FDA-approved for cosmetic lenses |
Sterilization | 121 °C moist heat, 30 minutes, F0 ≥ 30, SAL 1 ppm |
Quality control | 12 inspection steps within 20+ production procedures; 17× magnification screening |
Certifications | ISO 13485 quality management; U.S. FDA-registered facility (FEI 3015587162); CFDA registration |
Custom service | OEM / ODM, pattern proofing, custom packaging |
A factory visit is worth the travel only if it ends with a decision. This delegation left with three: two designs for a trial run, artwork checked against their market's labelling requirements, and a written production window for the first batch.
If you are planning a similar visit, bring these three and the day becomes a working session rather than a tour:
Your market's registration requirements — the documents your authority will ask for. They can be checked against the factory's records on the spot.
Your target retail price band — it fixes material grade, diameter and packaging format before any quotation is meaningful.
A packaging reference or mock-up — the fastest way to settle blister, carton and insert specifications.
Factory visits can be arranged for distributors, importers and private-label brand owners. Write to Sales@haipuminglens.com, or message +86 176 0731 1512 / +86 189 3243 5573 on WhatsApp with your market, the categories you carry and your expected volumes.
− About Hunan Haipuming: capacity, timeline and equipment
− Quality: 12 inspection steps, pigment sourcing and sterilization
− OEM / ODM and custom packaging
Four things a sample cannot show: where the pigment comes from and whether it is approved for cosmetic lenses, whether print registration holds across the run, what the sterilization parameters and records are, and whether a blister can be traced back to its mould and lot.
One working day covers the company introduction, the full production route, the inspection line, packing and a commercial discussion. Buyers reviewing artwork or packaging mock-ups usually allow a second half-day.
Terminal moist heat sterilization at 121 °C for 30 minutes, F0 ≥ 30, with the sterility assurance level held at one part per million. Parameters are recorded per load.
Yes. Pattern proofing is available before production, so the iris design and colour can be approved on a physical sample rather than a screen rendering.
ISO 13485 quality management documentation, the U.S. FDA facility registration (FEI 3015587162) and the CFDA registration. Buyers can also review batch records and inspection logs for the lot being produced.
Hunan Haipuming Technology Co., Ltd. — a coloured contact lens factory of Hunan Liangguo Technology Group. ISO 13485 quality management, FDA-registered facility (FEI 3015587162), CFDA-registered production.